View MIC442005_4223236.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

MIC4420/4429
Micrel, Inc.
MIC4420/4429
6A-Peak Low-Side MOSFET Driver Bipolar/CMOS/DMOS Process
General Description
MIC4420, MIC4429 and MIC429 MOSFET drivers are tough, efficient, and easy to use. The MIC4429 and MIC429 are inverting drivers, while the MIC4420 is a non-inverting driver. They are capable of 6A (peak) output and can drive the largest MOSFETs with an improved safe operating margin. The MIC4420/4429/429 accepts any logic input from 2.4V to VS without external speed-up capacitors or resistor networks. Proprietary circuits allow the input to swing negative by as much as 5V without damaging the part. Additional circuits protect against damage from electrostatic discharge. MIC4420/4429/429 drivers can replace three or more discrete components, reducing PCB area requirements, simplifying product design, and reducing assembly cost. Modern BiCMOS/DMOS construction guarantees freedom from latch-up. The rail-to-rail swing capability insures adequate gate voltage to the MOSFET during power up/down sequencing. Note: See MIC4120/4129 for high power and narrow pulse applications.
Features
* CMOS Construction * Latch-Up Protected: Will Withstand >500mA Reverse Output Current * Logic Input Withstands Negative Swing of Up to 5V * Matched Rise and Fall Times ................................ 25ns * High Peak Output Current ............................... 6A Peak * Wide Operating Range ............................... 4.5V to 18V * High Capacitive Load Drive ............................10,000pF * Low Delay Time .............................................. 55ns Typ * Logic High Input for Any Voltage From 2.4V to VS * Low Equivalent Input Capacitance (typ) ..................6pF * Low Supply Current ...............450A With Logic 1 Input * Low Output Impedance ......................................... 2.5 * Output Voltage Swing Within 25mV of Ground or VS
Applications
* * * * Switch Mode Power Supplies Motor Controls Pulse Transformer Driver Class-D Switching Amplifiers
Functional Diagram
VS
0.1mA
0.4mA
MIC4429 IN V E R T I N G
OUT
IN
2k
MIC4420 NONINVERTING
GND
Micrel, Inc. * 2180 Fortune Drive * San Jose, CA 95131 * USA * tel + 1 (408) 944-0800 * fax + 1 (408) 474-1000 * http://www.micrel.com
July 2005
1
M9999-072205
MIC4420/4429
Micrel, Inc. Temperature Range 0C to +70C -40C to +85C 0C to +70C -40C to +85C -40C to +85C 0C to +70C 0C to +70C -40C to +85C 0C to +70C -40C to +85C -40C to +85C 0C to +70C
Ordering Information
Part No. Standard Pb-Free MIC4420CN MIC4420ZN MIC4420BN MIC4420YN MIC4420CM MIC4420ZM MIC4420BM MIC4420YM MIC4420BMM MIC4420YMM MIC4420CT MIC4420ZT MIC4429CN MIC4429ZN MIC4429BN MIC4429YN MIC4429CM MIC4429ZM MIC4429BM MIC4429YM MIC4429BMM MIC4429YMM MIC4429CT MIC4429ZT Package 8-Pin PDIP 8-Pin PDIP 8-Pin SOIC 8-Pin SOIC 8-Pin MSOP 5-Pin TO-220 8-Pin PDIP 8-Pin PDIP 8-Pin SOIC 8-Pin SOIC 8-Pin MSOP 5-Pin TO-220 Configuration Non-Inverting Non-Inverting Non-Inverting Non-Inverting Non-Inverting Non-Inverting Inverting Inverting Inverting Inverting Inverting Inverting
Pin Configurations
VS 1
IN 2
NC 3
GND 4
8 VS 7 OUT 6 OUT 5 GND
Plastic DIP (N) SOIC (M) MSOP (MM)
5 4 3 2 1
TO-220-5 (T)
OUT GND VS GND IN
Pin Description
Pin Number TO-220-5 1 2, 4 3, TAB 5 Pin Number DIP, SOIC, MSOP 2 4, 5 1, 8 6, 7 3 Pin Name IN GND OUT NC VS Pin Function Control Input Ground: Duplicate pins must be externally connected together. Supply Input: Duplicate pins must be externally connected together. Output: Duplicate pins must be externally connected together. Not connected.
M9999-072205
2
July 2005
MIC4420/4429
Micrel, Inc.
Absolute Maximum Ratings (Notes 1, 2 and 3)
Supply Voltage ...........................................................20V Input Voltage ............................... VS + 0.3V to GND - 5V Input Current (VIN > VS) .......................................... 50mA Power Dissipation, TA 25C PDIP ....................................................................960W SOIC ...............................................................1040mW 5-Pin TO-220 ...........................................................2W Power Dissipation, TC 25C 5-Pin TO-220 ......................................................12.5W Derating Factors (to Ambient) PDIP .............................................................7.7mW/C SOIC .............................................................8.3mW/C 5-Pin TO-220 .................................................17mW/C Storage Temperature............................. -65C to +150C Lead Temperature (10 sec.) ................................... 300C
Operating Ratings
Supply Voltage .............................................. 4.5V to 18V Junction Temperature ............................................. 150C Ambient Temperature C Version ................................................. 0C to +70C B Version ............................................. -40C to +85C Package Thermal Resistance 5-pin TO-220 (JC) ............................................10C/W 8-pin MSOP (JA) ...........................................250C/W
Electrical Characteristics:
Symbol INPUT VIH VIL IIN VIN OUTPUT VOH VOL RO RO IPK IR High Output Voltage Low Output Voltage Output Resistance, Output Low Output Resistance, Output High Peak Output Current Logic 1 Input Voltage Logic 0 Input Voltage Input Voltage Range Input Current Parameter
(TA = 25C with 4.5V VS 18V unless otherwise specified. Note 4.) Conditions Min 2.4 -5 0 V VIN VS See Figure 1 See Figure 1 IOUT = 10 mA, VS = 18 V IOUT = 10 mA, VS = 18 V VS = 18 V (See Figure 6) -10 VS-0.025 1.7 1.5 6 >500 Typ 1.4 1.1 0.8 VS + 0.3 10 Max Units V V V A V 0.025 2.8 2.5 V A mA
Latch-Up Protection Withstand Reverse Current Rise Time Fall Time Delay Time Delay Time Power Supply Current Operating Input Voltage
SWITCHING TIME (Note 3) tR tF tD1 tD2 IS VS Test Figure 1, CL = 2500 pF Test Figure 1 Test Figure 1 VIN = 3 V VIN = 0 V Test Figure 1, CL = 2500 pF 12 13 18 48 0.45 90 4.5 35 35 75 75 1.5 150 18 ns ns ns ns mA A V
POWER SUPPLY
July 2005
3
M9999-072205
MIC4420/4429
Micrel, Inc.
Conditions Min 2.4 0.8 -5 0V VIN VS Figure 1 Figure 1 IOUT = 10mA, VS = 18V IOUT = 10mA, VS = 18V -10 VS-0.025 3 2.3 VS + 0.3 10 Typ Max Units V V V A V 0.025 5 5 V
Electrical Characteristics: (TA = -55C to +125C with 4.5V VS 18V unless otherwise specified.)
Symbol INPUT VIH VIL IIN VIN OUTPUT VOH VOL RO RO High Output Voltage Low Output Voltage Output Resistance, Output Low Output Resistance, Output High Rise Time Fall Time Delay Time Delay Time Power Supply Current Operating Input Voltage Logic 1 Input Voltage Logic 0 Input Voltage Input Voltage Range Input Current Parameter
SWITCHING TIME (Note 3) tR tF tD1 tD2 IS VS Figure 1, CL = 2500pF Figure 1 Figure 1 VIN = 3V VIN = 0V Figure 1, CL = 2500pF 32 34 50 65 0.45 0.06 4.5 60 60 100 100 3.0 0.4 18 ns ns ns ns mA mA V
POWER SUPPLY
Note 1: Note 2: Note 3: Note 4:
Functional operation above the absolute maximum stress ratings is not implied. Static-sensitive device. Store only in conductive containers. Handling personnel and equipment should be grounded to prevent damage from static discharge. Switching times guaranteed by design. Specification for packaged product only.
Test Circuits
0.1F
VS = 18V 0.1F 1.0F
VS = 18V
0.1F
0.1F
1.0F
IN MIC4429
OUT 2500pF
IN MIC4420
OUT 2500pF
INPUT
5V 90% 10% 0V
2.5V tP W 0.5s
tD1
INPUT
5V 90% 10% 0V
2.5V tP W 0.5s
tD1
tP W
VS 90%
tF
tD2
tR
tP W
VS 90%
tR
tD2
tF
O U TPU T
10% 0V
O U TPU T
10% 0V
Figure 1. Inverting Driver Switching Time
M9999-072205
Figure 2. Noninverting Driver Switching Time 4 July 2005
MIC4420/4429
Micrel, Inc.
Typical Characteristic Curves
60 50 40
Rise Time vs. Supply Voltage
50 40
Fall Time vs. Supply Voltage
Rise and Fall Times vs. Temperature
25 20
C L = 2200 pF VS = 18V
C L = 10,000 pF
C L = 10,000 pF
TIME (ns)
TIME (ns)
TIME (ns)
30 20 10 0
C L = 4700 pF
C L = 2200 pF
15 10 5 0 -60
30 20 10 0
5 7 9
t FALL
C L = 4700 pF
C L = 2200 pF
t RISE
11 VS (V)
13
15
5
7
9
11 VS (V)
13
15
-20 20 60 100 TEMPERATURE (C)
140
Rise Time vs. Capacitive Load
50 40
30
50
40
30
Fall Time vs. Capacitive Load
60 50
Delay Time vs. Supply Voltage
tD2
DELAY TIME (ns)
TIME (ns)
20
TIME (ns)
VS = 5V
20
40 30 20 10
VS = 5V
VS = 12V
VS = 18V
VS = 12V
10
VS = 18V
10
tD1
5 1000
3000 CAPACITIVE LOAD (pF )
10,000
5 1000
3000 CAPACITIVE LOAD (pF )
10,000
0
4
6
8 10 12 14 16 SUPPLY VOLTAGE (V)
18
60 50
Propagation Delay Time vs. Temperature
t D2
Supply Current vs. Capacitive Load
84
Supply Current vs. Frequency
1000
VS = 15V
CL = 2200 pF
18V
IS - SUPPLY CURRENT (mA)
SUPPLY CURRENT (mA)
70 56 42 28 14 0
0
500 kHz
TIME (ns)
100
10V
40 30 20 10 -60
5V
t D1
10
200 kHz
C L = 2200 pF V S = 18V
-20 20 60 100 TEMPERATURE (C) 140
20 kHz
100 1000 CAPACITIVE LOAD (pF )
10,000
0
0
100 1000 FREQUENCY (kHz)
10,000
July 2005
5
M9999-072205
MIC4420/4429
Micrel, Inc.
Typical Characteristic Curves (Cont.)
Quiescent Power Supply Voltage vs. Supply Current
900 800 700 600 500 400 -60
1000 800 600 400 200 0
Quiescent Power Supply Current vs. Temperature
LOGIC "1" INPUT VS = 18V
SUPPLY CURRENT (A)
LOGIC "1" INPUT
LOGIC "0" INPUT
0 4 8 12 16 SUPPLY VOLTAGE (V) 20
SUPPLY CURRENT (A)
-20
20 60 100 TEMPERATURE (C)
140
High-State Output Resistance
5
Low-State Output Resistance
2.5
100 mA
ROUT (W)
10 mA
ROUT (W)
4
50 mA
2
100 mA
50 mA
1.5
3
10 mA
2
5
7
9
11 VS (V)
13
15
1
5
7
9
11 VS (V)
13
15
200 160
Effect of Input Amplitude on Propagation Delay
LOAD = 2200 pF
-8
Crossover Area vs. Supply Voltage
2.0
PER TRANSITION
1.5
120 80 40 0
INPUT 2.4V
CROSSOVER AREA (A*s) x 10
DELAY (ns)
INPUT 3.0V
1.0
INPUT 5.0V
INPUT 8V AND 10V
0.5
5
6
7
8
9 10 11 12 13 14 15 VS (V)
0
5
6
7 8 9 10 11 12 13 14 15 SUPPLY VOLTAGE V (V)
S
M9999-072205
6
July 2005
MIC4420/4429
Micrel, Inc.
Applications Information Supply Bypassing
Charging and discharging large capacitive loads quickly requires large currents. For example, charging a 2500pF load to 18V in 25ns requires a 1.8 A current from the device power supply. The MIC4420/4429 has double bonding on the supply pins, the ground pins and output pins This reduces parasitic lead inductance. Low inductance enables large currents to be switched rapidly. It also reduces internal ringing that can cause voltage breakdown when the driver is operated at or near the maximum rated voltage. Internal ringing can also cause output oscillation due to feedback. This feedback is added to the input signal since it is referenced to the same ground. To guarantee low supply impedance over a wide frequency range, a parallel capacitor combination is recommended for supply bypassing. Low inductance ceramic disk capacitors with short lead lengths (< 0.5 inch) should be used. A 1F low ESR film capacitor in parallel with two 0.1 F low ESR ceramic capacitors, (such as AVX RAM GUARD(R)), provides adequate bypassing. Connect one ceramic capacitor directly between pins 1 and 4. Connect the second ceramic capacitor directly between pins 8 and 5.
Grounding
The high current capability of the MIC4420/4429 demands careful PC board layout for best performance Since the MIC4429 is an inverting driver, any ground lead impedance will appear as negative feedback which can degrade switching speed. Feedback is especially noticeable with slow-rise time inputs. The MIC4429 input structure includes 300mV of hysteresis to ensure clean transitions and freedom from oscillation, but attention to layout is still recommended. Figure 3 shows the feedback effect in detail. As the MIC4429 input begins to go positive, the output goes negative and several amperes of current flow in the ground lead. As little as 0.05 of PC trace resistance can produce hundreds of millivolts at the MIC4429 ground pins. If the driving logic is referenced to power ground, the effective logic input level is reduced and oscillation may result. To insure optimum performance, separate ground traces should be provided for the logic and power connections. Connecting the logic ground directly to the MIC4429 GND pins will ensure full logic drive to the input and ensure fast output switching. Both of the MIC4429 GND pins should, however, still be connected to power ground.
+15
(x2) 1N4448
5.6 k 560
0.1F 50V
+
1
2
1F 50V MKS2
6, 7
+
BYV 10 (x 2)
8
0.1F WIMA MKS2
MIC4429
4 5
220 F 50V + 35 F 50V
UNIT E D CHE MCON S X E
Figure 3. Self-Contained Voltage Doubler
July 2005
7
M9999-072205
MIC4420/4429
Micrel, Inc. attention should be given to power dissipation when driving low impedance loads and/or operating at high frequency. The supply current vs frequency and supply current vs capacitive load characteristic curves aid in determining power dissipation calculations. Table 1 lists the maximum safe operating frequency for several power supply voltages when driving a 2500pF load. More accurate power dissipation figures can be obtained by summing the three dissipation sources. Given the power dissipation in the device, and the thermal resistance of the package, junction operating temperature for any ambient is easy to calculate. For example, the thermal resistance of the 8-pin MSOP package, from the data sheet, is 250C/W. In a 25C ambient, then, using a maximum junction temperature of 150C, this package will dissipate 500mW. Accurate power dissipation numbers can be obtained by summing the three sources of power dissipation in the device: * Load Power Dissipation (PL) * Quiescent power dissipation (PQ) * Transition power dissipation (PT) Calculation of load power dissipation differs depending on whether the load is capacitive, resistive or inductive. Resistive Load Power Dissipation Dissipation caused by a resistive load can be calculated as: PL = I2 RO D where: I = the current drawn by the load RO = the output resistance of the driver when the output is high, at the power supply voltage used. (See data sheet) D = fraction of time the load is conducting (duty cycle)
Input Stage
The input voltage level of the 4429 changes the quiescent supply current. The N channel MOSFET input stage transistor drives a 450A current source load. With a logic "1" input, the maximum quiescent supply current is 450A. Logic "0" input level signals reduce quiescent current to 55A maximum. The MIC4420/4429 input is designed to provide 300mV of hysteresis. This provides clean transitions, reduces noise sensitivity, and minimizes output stage current spiking when changing states. Input voltage threshold level is approximately 1.5V, making the device TTL compatible over the 4 .5V to 18V operating supply voltage range. Input current is less than 10A over this range. The MIC4429 can be directly driven by the TL494, SG1526/1527, SG1524, TSC170, MIC38HC42 and similar switch mode power supply integrated circuits. By offloading the power-driving duties to the MIC4420/4429, the power supply controller can operate at lower dissipation. This can improve performance and reliability. The input can be greater than the +VS supply, however, current will flow into the input lead. The propagation delay for TD2 will increase to as much as 400ns at room temperature. The input currents can be as high as 30mA p-p (6.4mARMS) with the input, 6 V greater than the supply voltage. No damage will occur to MIC4420/4429 however, and it will not latch. The input appears as a 7pF capacitance, and does not change even if the input is driven from an AC source. Care should be taken so that the input does not go more than 5 volts below the negative rail.
Power Dissipation
CMOS circuits usually permit the user to ignore power dissipation. Logic families such as 4000 and 74C have outputs which can only supply a few milliamperes of current, and even shorting outputs to ground will not force enough current to destroy the device. The MIC4420/4429 on the other hand, can source or sink several amperes and drive large capacitive loads at high frequency. The package power dissipation limit can easily be exceeded. Therefore, some
+18 V
Table 1: MIC4429 Maximum
WIMA MKS-2 1 F
Operating Frequency VS Max Frequency 500kHz 700kHz 1.6MHz
1. DIP Package (JA = 130C/W) 2. TA = 25C 3. CL = 2500pF
5.0V
1 8
MIC4429
6, 7
TE K C U R R E N T P ROB E 6 3 0 2
18 V
0V
0.1F
4
5
0.1F
0V
2,500 pF POLYCARBONATE
18V 15V 10V
Conditions:
LOGIC GROUND
6 AMPS 300 mV PC TRACE RESISTANCE = 0.05
POWER GROUND
Figure 4. Switching Time Degradation Due to Negative Feedback
M9999-072205
8
July 2005
MIC4420/4429 Capacitive Load Power Dissipation Dissipation caused by a capacitive load is simply the energy placed in, or removed from, the load capacitance by the driver. The energy stored in a capacitor is described by the equation: E = 1/2 C V2 As this energy is lost in the driver each time the load is charged or discharged, for power dissipation calculations the 1/2 is removed. This equation also shows that it is good practice not to place more voltage on the capacitor than is necessary, as dissipation increases as the square of the voltage applied to the capacitor. For a driver with a capacitive load: PL = f C (VS)2 where: f = Operating Frequency C = Load Capacitance VS =Driver Supply Voltage Inductive Load Power Dissipation For inductive loads the situation is more complicated. For the part of the cycle in which the driver is actively forcing current into the inductor, the situation is the same as it is in the resistive case: PL1 = I2 RO D However, in this instance the RO required may be either the on resistance of the driver when its output is in the high state, or its on resistance when the driver is in the low state, depending on how the inductor is connected, and this is still only half the story. For the part of the cycle when the inductor is forcing current through the driver, dissipation is best described as PL2 = I VD (1-D) where VD is the forward drop of the clamp diode in the driver (generally around 0.7V). The two parts of the load dissipation must be summed in to produce PL PL = PL1 + PL2 Quiescent Power Dissipation Quiescent power dissipation (PQ, as described in the input section) depends on whether the input is high or low. A low input will result in a maximum current drain (per driver) of 0.2mA; a logic high will result in a current drain of 2.0mA. Quiescent power can therefore be found from: PQ = VS [D IH + (1-D) IL] where: IH = IL = D= VS =
Micrel, Inc. quiescent current with input high quiescent current with input low fraction of time input is high (duty cycle) power supply voltage
Transition Power Dissipation Transition power is dissipated in the driver each time its output changes state, because during the transition, for a very brief interval, both the N- and P-channel MOSFETs in the output totem-pole are ON simultaneously, and a current is conducted through them from V+S to ground. The transition power dissipation is approximately: PT = 2 f VS (A*s) where (A*s) is a time-current factor derived from the typical characteristic curves. Total power (PD) then, as previously described is: PD = PL + PQ +PT Definitions CL = Load Capacitance in Farads. D = Duty Cycle expressed as the fraction of time the input to the driver is high. f = Operating Frequency of the driver in Hertz IH = Power supply current drawn by a driver when both inputs are high and neither output is loaded. IL = Power supply current drawn by a driver when both inputs are low and neither output is loaded. ID = Output current from a driver in Amps. PD = Total power dissipated in a driver in Watts. PL = Power dissipated in the driver due to the driver's load in Watts. PQ = Power dissipated in a quiescent driver in Watts. PT = Power dissipated in a driver when the output changes states ("shoot-through current") in Watts. NOTE: The "shoot-through" current from a dual transition (once up, once down) for both drivers is shown by the "Typical Characteristic Curve : Crossover Area vs. Supply Voltage and is in ampere-seconds. This figure must be multiplied by the number of repetitions per second (frequency) to find Watts. RO = Output resistance of a driver in Ohms. VS = Power supply voltage to the IC in Volts.
July 2005
9
M9999-072205
MIC4420/4429
Micrel, Inc.
+18 V
WIMA MK22 1 F
5.0V
1
2
0V
8
MIC4429
6, 7
TE K C U R R E N T PROBE 6302
18 V
0.1F
4
5
0.1F
0V
10,000 pF PO L YC AR BO N AT E
Figure 5. Peak Output Current Test Circuit
M9999-072205
10
July 2005
MIC4420/4429
Micrel, Inc.
Package Information
PIN 1 DIMENSIONS: INCH (MM)
0.380 (9.65) 0.370 (9.40)
0.135 (3.43) 0.125 (3.18)
0.255 (6.48) 0.245 (6.22) 0.300 (7.62) 0.013 (0.330) 0.010 (0.254)
0.018 (0.57) 0.100 (2.54)
0.130 (3.30) 0.0375 (0.952)
0.380 (9.65) 0.320 (8.13)
8-Pin Plastic DIP (N)
8-Pin SOIC (M)
July 2005
11
M9999-072205
MIC4420/4429
Micrel, Inc.
0.112 (2.84)
0.187 (4.74)
INCH (MM)
0.116 (2.95)
0.032 (0.81)
0.038 (0.97)
0.012 (0.30) R
0.007 (0.18) 0.005 (0.13)
0.012 (0.03)
0.0256 (0.65) TYP
0.004 (0.10)
5 0 MIN
0.012 (0.03) R
0.035 (0.89)
0.021 (0.53)
8-Pin MSOP (MM)
0.150 D 0.005 (3.81 D 0.13) 0.400 0.015 (10.16 0.38) 0.108 0.005 (2.74 0.13) 0.177 0.008 (4.50 0.20) 0.050 0.005 (1.27 0.13)
0.241 0.017 (6.12 0.43)
0.578 0.018 (14.68 0.46)
SEATING PLANE
7 Typ. 0.550 0.010 (13.97 0.25)
0.067 0.005 (1.70 0.127)
0.268 REF (6.81 REF)
0.032 0.005 (0.81 0.13)
0.018 0.008 (0.46 0.20)
0.103 0.013 (2.62 0.33)
Dimensions:
inch (mm)
5-Lead TO-220 (T)
MICREL INC.
TEL + 1 (408) 944-0800 FAX + 1 (408) 474-1000 WEB http://www.micrel.com
2180 FORTUNE DRIVE
SAN JOSE, CA 95131
USA
This information furnished by Micrel in this data sheet is believed to be accurate and reliable. However no responsibility is assumed by Micrel for its use. Micrel reserves the right to change circuitry and specifications at any time without notification to the customer. Micrel Products are not designed or authorized for use as components in life support appliances, devices or systems where malfunction of a product can reasonably be expected to result in personal injury. Life support devices or systems are devices or systems that (a) are intended for surgical implant into the body or (b) support or sustain life, and whose failure to perform can be reasonably expected to result in a significant injury to the user. A Purchaser's use or sale of Micrel Products for use in life support appliances, devices or systems is a Purchaser's own risk and Purchaser agrees to fully indemnify Micrel for any damages resulting from such use or sale. (c) 2001 Micrel, Inc. M9999-072205
12
July 2005

▲Up To Search▲

Price & Availability of MIC442005

	To Download MIC442005 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .